Slide Mounting Media
Electron Microscopy Sciences EMbed-812 kit, 1 kit
Replacement for the discontinued Epon-812. Produces the same results in terms of preservation, handling, sectioning, and staining as the old Epon-812. Kit consists of 450 ml EMbed-812, 450 ml DDSA; Specially Distilled, 450 ml NMA, and *50 ml DMP-30. *Please note that wherever DMP-30 is listed as the accelerator in our embedding media kits you have the option to use BDMA in place of it. BDMA is less viscous, has a longer shelf life, and offers better penetration (it should be noted, however, that in order to achieve the optimum results when using BDMA in place of DMP-30 you must vary the amount. DMP-30: 1.5-2%; BDMA: 2.5-3%).
Electron Microscopy Sciences EMS Silver Colloidal Extender 25 ML
Extender for liquid and paste colloidal silver adhesive used in scanning electron microscopy.
Electron Microscopy Sciences EMS Colloidal Graphite, Alcohol Base 30 GR
Isopropal base collodal graphite has a Flat surface texture. The average flake size is 1 micron. Service temperature is 204 degree C.
Electron Microscopy Sciences Low viscosity embedding media kit, 1 kit
Provides excellent penetration for embedding biological tissues and rapid infiltration. Easy to prepare. The hardness is adjusted by changing the proportion of the flexibilizer (DER 736). The blocks have good trimming and sectioning qualities. Thin sections are tough under the electron beam. Kit consists of: 450 ml NSA, 225 ml ERL 4221 , 225 ml DER 736 , 25 ml DMAE.
Electron Microscopy Sciences Colloidal Silver Liquid, 15 g
1-Methoxy-2-propanol base. Fast drying. Average grain size less than 1 µm and Silver content is 60%. Sheet resistance is 0.02 ohm per square inch at 1 mil thickness. Comes with a brush attached to the cap. Service temperature is 30 minutes at 200°C.
Electron Microscopy Sciences Quetol 651/NSA Embedding Kit
A water miscible epoxy resin used for both light and electron microscopy. Its low viscosity permits easy infiltration and embedding, and yields light-colored blocks. Kit consists of: 225 ml Quetol 651, 450 ml NMA , 450 ml NSA, 50 ml
Electron Microscopy Sciences Technovit 8100 Embedding Kit
Technovit Glycol Methacrylate embedding kits developed by Kulzer in Germany are the most convenient to use and offers the best embedding results. Kits give better results offering improved morphology and allows for 1 micron serial sectioning. Polymerization temperature never exceeds 40 degree C, which makes either kit a potential choice for enzyme histochemistry.
The initiator is prepackaged, eliminating messy handling of dry components, and by eliminating aromatic amines from the formation, the components are significantly less toxic. The consistent high quality of raw materials used to make the resin allows for a permanent clear colorless block and, most important, reproducible results
Electron Microscopy Sciences EMbed 812, 450ml
EMbed 812 has the same characteristics as Epon 812, physically, and provides the same results in preservation, handling, curing and sectioning. EMbed 812 may cause etching on selected plastics. All formulas for mixing and using Epon 812 can be applied to EMbed 812
Electron Microscopy Sciences Technovit 3040 Mounting Medium Kit
Technovit 3040 yellow is a fast curing methyl methacrylate-based resin, whose chemical composition warrants a firm, durable bond between Technovit and the specimen.
Technovit 3040 consists of two components–powder and liquid–allowing simple mixing, easy adherance to the specimen, and fast curing. For fixing the mount, a high viscous consistency is required(i.e. a mixing ratio of approximately 2-3 parts per volume powder: 1 part per volume liquid) has proven to be the most advantageous.
Electron Microscopy Sciences Dapi Fluoromount G 20ML
DAPI-Fluoromont G is a water-soluble, instant blue nuclear probe fluorescing (455nm) compound for mounting fixed slides using a staining procedure having an aqueous final step. Mounting slides with DAPI Fluoromont G stains the cell nucleus and may reduce fluorochrome quenching during analysis of slides by fluorescence microscopy. this mounting medium also provides a semi permanent seal for long term storage of slide preparations.
Electron Microscopy Sciences Acrytol Mounting Medium 16 OZ
Acrytol is a rapid-drying mounting medium which enables slides to be screened immediately. It has a low viscosity, allowing the medium to flow easily. It also prevents air bubbles from becoming trapped. Acrytol contains an antioxidant to inhibit stain fading and prevent the formulation of annual rings. A thin coating of Acrytol is all that is needed to adhere a coverglass to a microscope slide.
Abcam Anti-Fade Fluorescence Mounting Medium - Aqueous, Fluoroshield, 250ML
Anti-fade fluorescence mounting medium (previously called fluoroshield mounting medium) is an aqueous mounting medium designed to preserve fluorescence when imaging tissues and cell samples. - Cited in over 30 publications - Contains 84% water - Fluorescence remains stable at 4°C in the dark - Prevents rapid photobleaching of key fluorophores
The product is subject to the following: Abcam Restricted Use Statement
Electron Microscopy Sciences Citifluor™ Mountant Solution AF1, Glycerol Based, Non Hardening 100 ML
Citifluor mounting medium for immunofluorescence is designed to reduce the fading of the fluorescence of dyes used for labeling biological specimens. In the technique of fluorescence microscopy, the fluorescence is stimulated by high intensity UV and/or visible light. Absorption of the light populates an excited state of the dye (usually a singlet state) and this leads to fluorescence. However, the excited state of the dye may undergo chemical reaction, which leads to destruction as evidenced by the fading of the fluorescence and consequent loss of the image. A glycerol-PBS solution contains an amine antifadent.
Material: Glycerol Based
Type: Non Hardening